Check Video Cable on HP Monitor: Fixed

Are you one of those who are facing Check video Cable on HP Monitor error? If you are searching solution for this problem then you are at the right spot because this article is going to help you in solving this issue. 

 Keep on reading to find the best solution for Check Video Cable on HP Monitor.


How To Fix Check Video Cable On Your HP Monitor Error:


The term “Check Video Cable on HP Monitor” refers to the cable that connects your computer to your monitor. 

It was given this message because if you have any issues with the cable, such as it being loose or unresponsive, the phrase “check video cable” will appear on your ho monitor, alerting you to the issue. 

This warning may also appear if your computer’s video card is faulty and is unable to transfer the necessary visual signal to your monitor via a cable.

You hit the power button as usual, and your computer turns on normally no buzzing sounds, lights blinking, fans spinning but your monitor read, “Check video cable,” and then shows you a black screen. 

Try the following steps to remedy the Check video cable on your HP monitor:

Restart Your Computer:

Occasionally, the No Video Input issue is only a momentary error that may be resolved by restarting your computer. 

By pushing and holding the power button for 3 to 5 seconds, you can force your computer to shut off. After that, turn it back on.

If your problem remains after rebooting, move on to the next Step.

There are a few things you can do to make sure your PC’s signal cord is operating correctly, depending on what kind of equipment you have. 

1st Step:

Make sure your signal cord is firmly connected to both your computer and your computer monitor. 

Either device should be securely connected to the plastic socket on each end of the cord. 

If you press the plug on the end of the cable and pull it toward the device, it should not move if it is completely put into its hole.

2nd Step:

Use a different monitor with your signal line. If you have a spare monitor at home, connect it to your computer instead of the one you’re presently using. 

If you continue to get a “No Signal” warning on your screen, the issue is most likely with your original computer display rather than the signal line. 

If the second monitor does not operate as well as the first, you have a signal cable problem that will require replacement.

You’ll see the classic “No Signal” warning on screen if your display problems are caused by a hardware issue.

You will see the standard PC desktop on-screen if everything works fine when testing the second monitor.

3rd Step

Use a separate computer to test your signal cable. If you have an older computer at home (or access to one), try connecting your current monitor to it. 

You do not need to connect your keyboard, mouse, or any other peripheral devices. Simply connect the computer’s power wire to a wall outlet, attach the signal cable to the computer’s back, and turn it on. 

If you keep getting a “Check Video Cable” warning on your screen, the issue is most likely with your computer’s video card rather than the signal line.

If the second computer does not operate, you have a signal cable problem that will require replacement.

You’ll see the classic “No Signal” warning on screen if your display problems are caused by a hardware issue. 

If everything goes well when testing the second computer, the usual PC desktop will appear on the screen.

Disconnect All Of Your Devices:

Peripherals attached to your computer may also cause your display to stop working correctly, resulting in the No Video Input error. 

Disconnect all peripherals and check if it solves the problem. Here’s how to do it:

  • Hold the power button down until your computer shuts off.
  • Remove all peripherals from the system.
  • Restart your computer if necessary.

If your display is working well, one of the peripherals you removed is the source of the problem. Each device should be reinstalled into your PC and tested each time. 

Then you’ll track down the precise gadget that’s causing your issue. Once you’ve located the malfunctioning device, replace it. Alternatively, contact the device’s manufacturer for support.

Reset The BIOS Settings:

Your monitor may also fail due to incorrect BIOS settings. You should reset your BIOS to factory settings to check if that’s the root of the problem. Here’s how you can do it:

  • Turn off your computer by pressing and holding the power button.
  • Disconnect the power supply’s AC power cord, then open your computer casing.
  • Using your fingernail or a non-conductive screwdriver, remove the CMOS battery from your motherboard.
  • This is how the CMOS battery appears.
  • Reinstall your CMOS battery after waiting 5 minutes.
  • Turn on your computer after connecting the AC power cord to the power supply.

You Might Like: Top 10 Best 144 Hz Monitor PS4: Buyer Guide & Review


Preventing Video Cable Issues In Future


Ensuring a seamless and trouble-free experience with your HP monitor requires not only knowing the cable issues but also how to prevent them. Here are some practical tips to help you avoid video cable problems in the future.

Handled With Care

Video cables are relatively delicate and susceptible to damage when handled roughly. To prevent any issue, refrain from sharply bending or kicking the video cable. When it comes to connecting or disconnecting the cable, do it gently.

Check Connections

Loose connections are the common culprit behind video-related problems. It is important to verify that the video cables are firmly and securely inserted in the HP monitor and the source device.

Prevent Pinching

It’s essential not to put heavy objects on or near the cables and prevent pinching between the monitor stand and the desk. Pinching can cause damage to the wires and potentially result in display issues.

Regular Inspection

Incorporate the practice of checking the video cables. Be vigilant in checking the apparent damages like worn out or bent wires. Detecting cable issues early can help you avoid future troubles.

Use Cable Organizers

Cable organizers, such as cable clips and sleeves, can help keep your video cable nearly organized and protected. They prevent excessive bending, reducing the risk of cable damage.

Proper Storage

When not in use, store your video cable in a safe manner. Avoid coiling it too tightly, as this can cause kinks and damage over time. Instead, use loops to store the video cable.

By following these tips you can significantly reduce the risk of cable damage in future. A maintained video cable gives you an enjoyable display on your HP monitor.

Also See: Can You Play Games on A Monitor Without a Pc


FAQs About Check Video Cable on HP Monitor


What is the best way to connect my computer to my monitor?

Between the computer and the display, connect the proper video cable. While attaching the video connection, be sure the computer is turned off.

Why do my PCs power up normally, but the monitor always displays “check video cable”?

You most likely switch on display first, then the computer. That’s what professionals do to ensure the monitor is operational.

How can I tell if my video cable is broken?

Verify that the Video Cable is visible on the screen. While attaching the video connection, be sure the computer is turned off.

Don’t Miss: Can You Use an All in One Computer as a Monitor


Final Words


If you are facing the Check Video Cable on HP Monitor, you are not alone. Many peoples are facing the same issue as yours. 

When a monitor identifies a connected connection but not a device or video card on the other end of that cable, check signal cable, and similar alerts appear. 

This frequently happens when a computer is turned off or when a video card isn’t installed properly.

Make sure the computer is turned on before disconnecting and reconnecting the cable to fix the problem. 

If the error remains, turn off the computer and double-check that the video card is properly placed. Make sure the right source is chosen in the setup menu if the display permits input from multiple sources.

Must Share:

My name is Aslam, and here is my story: I am a pickmonitors(Monitors) expert and have been in the field for over 6 years. I am currently working as a monitor expert and have done work for companies such as (Apple, Google, and Samsung).

Leave a Comment