Table of Contents
Samsung has a terrific monitor selection; however, they are known to have a number of issues.
The Samsung monitor not recognizing the HDMI problem is one such issue that many customers have noticed.
In this post we will provide you a solution of Samsung Monitor Not Detecting HDMI. So keep on reading full article if you are facing this issue:
Samsung Monitor Not Detecting HDMI:
If your Samsung Monitor is not detecting HDMI then you can try the following solutions:
Turn off and disconnect the monitor and computer to resolve the Samsung monitor not detecting HDMI issue. After 30 seconds, turn on your computer first, then your display.
If the problem persists, make sure you’ve selected the proper input and display resolution settings and that all cords are safe and undamaged.
If you’re having trouble with your Samsung monitor not detecting HDMI or not recognizing HDMI, try the troubleshooting steps listed below.
Some of these repairs need you to troubleshoot your display immediately, while others require you to troubleshoot your computer. We highly advise that you do these tasks in the sequence listed.
We’ll begin with the most basic repairs and work our way up to less common, more difficult troubleshooting procedures.
Unplug The Monitor And Restart The Computer:
Turn off and disconnect your display and computer before doing anything else. Plug everything back in after 30 seconds and switch on display first, then the computer.
The order is critical: switch on display first, then the computer.
Despite everything else, a large number of Samsung monitor owners have reported that this easy approach worked for them.
Change The monitor’s input settings:
If your Samsung monitor does not recognize HDMI, double-check that the Input setting is right. To begin, determine the type of input cord you’re using.
Your monitor’s Source/Input button will be in the center or on the right side. It’ll be on the backside or at the bottom of the display.
Some Samsung monitor variants need you to press the Menu button first and then choose Input.
Your monitor will display options once you push the Input and/or Menu buttons. Toggle through the input options until “HDMI” appears.
Examine The Cables That Connect The Monitors:
Let’s examine your display cable connections now that we’ve confirmed your monitor is configured to the right Input. First and foremost, ensure that both sides of the connection are secure.
One of the most typical causes of a Samsung monitor not recognizing HDMI error is a loose cable. Even if the connection is marginally damaged, an error might occur.
After that, inspect the cable for any problems or obstructions. Look for any apparent evidence of damage. Finally, try a different input cable than the HDMI one you’re using right now.
HDMI, Dp, and VGA are the most popular cables supported by Samsung displays. Determine the type of alternative cable you have.
If you’re trying out a new cable, make sure to repeat step 1 and set the display Input appropriately.
If switching to a different display cable fixes the problem, the problem was most likely caused by a malfunctioning display cable.
Change The Resolution Of Your Monitor:
Your Samsung monitor can send a variety of display resolutions back to your computer.
It’s conceivable that your computer’s graphic card is set to a display resolution that your monitor can’t support right now.
If this is the case, the Samsung monitor not detecting the HDMI message you’re getting might be the result.
In Safe Mode, your computer will use a lower screen resolution than it would otherwise. It will allow you to go into the resolution settings on your computer and pick a lower conventional display resolution.
Do you know what resolution a Samsung monitor could handle? You can choose between two options:
- Look for your Samsung model reference number of the monitor in the Samsung user manual search engine.
- Experiment with some trial-and-error. Increase your resolution in small increments. Wait thirty seconds for each update to check whether the notice “Samsung monitor not recognizing HDMI” appears.
You Might Also Like: What Is Overdrive on A Monitor? Advantages & Disadvantages
Check That The Display Cable Is Connected To The Graphic Card, Not The Motherboard:
Almost every desktop computer has an onboard graphics unit with appropriate ports on the rear.
If this is the case, make sure your display wire is linked to the graphic card rather than the motherboard. It’s often as simple as that with a desktop computer.
Remove The RAM Sticks, Reorder Them, And Then Reinstall Them:
It’s conceivable that your Samsung display is reporting no signal because your RAM sticks aren’t properly connected.
Ensure your computer is switched off and the power supply is unplugged from the socket to fix the problem.
After that, ground yourself properly, open your PC, and completely remove each of your RAM sticks. Finally, rearrange the sacks and re-insert them into their RAM seats.
Reset The CMOS/BIOS:
The abbreviation for Complementary Metal Oxide Semiconductor is CMOS.
The BIOS firmware is powered by the CMOS battery in your laptop or computer. BIOS stands for “Basic Input/output System,” and it’s in charge of all of your computer’s important functions.
Resetting your BIOS restores your computer’s previous settings and can often fix a wide range of issues.
Make sure your computer is switched off, the power cord is unplugged, and you’ve rooted correctly once again.
Disconnect the CMOS batteries from the board after that. Then press and holding button to drain any leftover power.
After about a minute, replace the CMOS battery in your computer. Finally, restart your computer and verify that your display is operational.
No Singal Despite The Connected HDMI
You get no signal message even though the HDMI cable is connected, it can be a frustrating experience. Here are several steps to resolve the issues.
Check the Connection And Restart Device
To troubleshoot a No signal issue on your monitor, begin by ensuring the HDMI cable is correctly connected to both your monitor and your computer or another video source.
Sometimes, a loose or imperfect connection can be the root cause of the problem. Additionally, try powering off both your monitor and the device connected to it, and then turn them back on.
This straightforward step can frequently reset the HDMI connected to it, providing a quick resolution to the issue. These initial checks and actions often address the No signal problem allowing you to enjoy uninterrupted connectivity between your device.
Correct Input Source
Your monitor may have multiple input sources, such as HDMI, VGA, or Display Port. Make sure you have selected the right source on your monitor’s menu. Using the on-screen display or physical buttons on your monitor, switch to the HDMI input.
Try Different HDMI Port
If your monitor has multiple HDMI ports, switch to a different one. It’s possible that one of the ports is malfunctioning, and trying another may establish a connection.
Check Display Setting
On your computer, go to display settings and ensure that it’s set to duplicate or extend the display to the monitor. Sometimes, the computer defaults to a different display mode.
Update Graphic Drivers
One more cause of this issue is outdated graphic cards. Make sure your graphic cards are up to date.
Test With Other Devices
To rule out the problem with the source device, try connecting your monitor to another computer or source with the same HDMI cable. if it works then the issue may be with your original device.
Why isn’t my Samsung display receiving HDMI signals?
The most typical explanation for a blank monitor is that it has been switched off, hibernated, or is on a screen saver and will wake up when Input is received.
What should I do if my Samsung monitor has to be reset?
If your monitor has a power switch on the back, check sure it’s turned on before pressing the front-panel power button.
Turn off and disconnect the monitor and computer to resolve the Samsung monitor not detecting HDMI issue.
After 30 seconds, turn on your computer first, then your display. If the problem persists, make sure you’ve selected the proper input and display resolution settings and that all cords are safe and undamaged.
It might be aggravating to see the Samsung monitor not recognizing HDMI messages. There’s no reason to be concerned.